Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
This great article below in relation to Tools You Need to Install a New Bathtub is exceedingly enjoyable. Don't miss it.
Installing a bath tub isn't specifically rocket science, but it does require strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old tub with a new one is likewise a moderately tough job. If the old bathtub is conveniently obtainable, the project can move quickly; if you need to open a wall surface to remove the old tub and also position the brand-new tub, the job is a lot harder. In either case, the task is within a residence handyman's abilities, although you will require a helper to vacate the old tub as well as embeded in the brand-new one. See to it you have certified on your own for the task and also fit trying it. Instead of hiring a specialist to take over a halfway-completed project, it is far better to consider employing one before you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will assist you install a brand-new tub in your bathroom if you have actually already bought a new bathtub as well as do not need to alter the plan of your previous water system pipelines.
Your devices as well as product checklist need to make up the following:
Getting ready for the Installment
Firstly, the supporting frame provided with the bath should be fitted (if needed) according to the producer's directions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to avoid pressure on the tub.
Fit the flexible tap connectors to the bottom of both faucets using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The procedure of removing the existing faucets can be fairly bothersome due to the limited accessibility that is typically the case.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will come from the pipes. As soon as the supply pipelines have actually been eliminated, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to moving on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Making use of the two wood boards under its feet, position the tub in the needed setting. The wooden boards are valuable in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The next goal is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as readjusting the feet on the bathtub up until the spirit level reads level.
To mount taps, fit all-time low of the furthest versatile tap adapter to the proper supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Switch on the supply of water and examine all joints and also new pipework for leaks as well as tighten them if necessary. Fill the bathtub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leaks.
Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as securing around the bathtub must wait till the bathtub has actually been used at least once as this will settle it right into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet connectors. The former kind must be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to split a rigid seal, causing the water to permeate the wall surface in between the bathroom as well as the tiling, causing issues with moisture and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and also cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to permit the movement experienced when the tub remains in use. The sealant can split fairly early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water-proof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading up on Tools You Need to Install a New Bathtub ? Create a review directly below. We'd be glad to hear your reactions about this entry. We are looking forward that you come back again in the near future. Sharing is nice. You never know, you may very well be doing someone a favor. I thank you for reading our article about How to Install a Bathtub Yourself.
Fix it ASAP! Call. Report this page